bondy

hello all can anybody addvice me on witch gasket sealant to buy? ive got a verry slight leak on the clutch case ive gone through tree gaskets now. cant understand why its leaking was ok when i first built the bike but since i took it back off to do the clutch its got a leak. so for good measure gonner put abit of sealant on. ive look on the net what avalabel theres loads to choose. would i be better with a non setting sealant so if i need to take the cover off for any reason i wont need to be hammering it off. please help

hello john im chris ive just finished my 199A 350 ive put new barnet clutch plates in got new push rod in and throw out ball. ive bottomed the clutch springs and backed them off 3/half turns as sevice manual say. is this the best way to set the clutch? your help would be mutch needed thanks chris

hello again steve ive just had a look at the gear end shaft and i noticed a metal ring. witch befor i thought it was part of the shaft but i was wrong. i got it out with a small flat driver. seal whent in no probs. i put seal in with spring facing out but oil still comming out so ill try it the other way.

i need your help please im struggling to put a new seal in the final end drive of the front sprocket. its doning my head in ive nearly finished my 199A and somthing so small is getting the better of me. it was leaking oil so ive changed the seal and bush behide the sprocket and o ring. im abit confused witch way the final end seal gose? normaly seals go with the open end inwards. but pete from bultaco uk said it gose in with the open end facing outwards? ive tryed taping it in but seem to damage the seal so your help would be mutch appriceated

can anybody help ive put new o ring and bush and seal behinde front sproket. put it all back together great a thought untill i had it running noticed it was still leaking. so i cheked were the oil was coming from. looks like its leaking behinede the felt pad so i give bultaco uk a ring and asked for there addvice. he said its the seal in the shaft i didnt know there was a seal there. so i got one tryed to put it in just want to know how fare in should it go in?

hello cheers for replying ive sorted the clutch now i think. shes kicking over ok now affter ajusting the clutch nuts. the carb is a 28mm bing had to put the right jets in didnt come with the right ones. still strugeling to get it started think its a fuel issue. i put fuel down the head fired up first kick. think the air scerw needs seting onces i get her going she onley idels with the chock on when i take chock off she dies unless i keep the reaves on. getting back to the clutch cups you couldnt understand. they was worn so got new ones

hi mate you was right the nuts needed more ajustment. so ive done that shes kicking over ok now. i started her up took quit a few kicks to get it started. dont think fuel is getting throw so i put some fuel down the head and she fired up no probs so i think its the carb. just somthing else i wanted to ask ive put a new seal behind the front sprocket including o ring but still leaking oil the felt pad is soaked in oil so asked bultaco uk pete said its the seal in the shaft were the push rod gose. one more thing when i put it in gear this dosent hapen all the time it makes a nose as if its not engaging could this mean the clutch needsmore ajusting? as for the cups one was worn well they all was so i got new ones put locking wire throw nuts to at a time is this ok?

hi can anybody help ive just finished my 199A just put a new clutch plates in barnet ones im trying to set it but kick starts turning over but sliping but just noticed one of the spring cups had pulled throw it had the metel ones in i thought it needed new plates but turned out the was no throw out ball so put one in i know its somthing supid im not doing gonner wait till new cups come and try again but your help might put some light on the matter i had it runing and she pulls ok just needs the carb settin i put the right jets in as it was a new carb from spain but didnt come with the right jets

thanks ill get sum

thanks for the addvice wheres the best place to get loctite?

hello all can anybody tell me whats the best way to seal the holes were the greas nipels go the only reason im sealing them is because ive put the rolling bush kit in ive tryd clear silicon and it just keeps coming out when its dry is there somthing else what would work?

thanks for the info ill just tie wrap it cheers

could anyboy tell me were the over flow tube gose on the chutch case? ive got it tuck inbeween the finns at the moment but wont it melt with the heat or is there a fitting that clips on the finns so the tube can go throw?

can you help me again my front wheel was wobbeling so i took it off and noticed one of the bearing was nackard so i took it out no probs came to do the other side and ive ended up with the outer race of the bearing still stuck inside it hasnt moved at all just the center came out can you help dont want to damage the hub

thank you for that mutch needed addvice would have never thought about the threads catching the case ive just put barnet plats in mine like you said there thicker the lock wire were do you get it from tryed halfords dont do it cant thick off anywere else

ok thanks for the addvice just one more thing the new clutch plats or in ive ajusted 6 nuts more or less the same and ajusted the grub srew pulled clutch leaver in and turnd it over clutch plats seem to be runing ok but whats the best way to set the 6 nunts and will 30 amp fuse wire be ok for the lock wire

hi john i got my 199A going had a blast round the back garden shes got sum power checkit over and tryed to start her up again but the kick start was sliping so i ajusted the clutch no joy so i thought it needed new clutch so i got a set off barnet ones off bultaco uk put them in had to bottom the scerw before the plates was openin so i checkt to see if the throw out ball was there to my horrer it wasnt there so ive just payed for clutch plates i probely didnt need the old ones look ok they have dipels in them anyway my question is the plates with the half moons and the slits in them witch go inbeween the clutch plates do the slits have to line up with eachother?

hi thanks for your photos ive got the headsteady on it was just awkward getting it on ill post photos when ive finished ive just got me wheels whats the best tape to use for the inner rim?

hi bj im intrested in the upgrade bash plate from todo trials can you tell me how did you ordder it coz ive tryed and its not happening

for my sherpa 350T 199A

hi its a steel one

hi all dose anybody know were i can get a stronger hesdsteady?

thaks for your help i have got the one and a half link so if i need it ive got it cheers

hi sorry i dont mean the bearing its the brake plate theres a groove that gose all the way round and a ruber seal seats in it thats on the rear breake plate any ideas were id get one from?

cheers andy i wont be fitting the towbar myself ill be getting my rack end off jan so ill let you know how i go thanks