you should not run the bime on eneything over 50:1 on castrol tts you might be doing damage to your engine i dought it but it might my bike makes terrible noises on 80:1 tts it specifies on the back of the bottle to not mix over 50:1
i had the same problem with my bike found out it was the kill switch wire was bare and touching the bars cutting the spark only other simple thing i can think of is the spark plug cap is not on the ht lead properly
this is what happened to my mates little brother this weekend hsi parents had decided to get him a 50cc crosser this kid was about five and had never riden a bike before he does not look very good on a bicycle so it was an accident waiting to happen eney way they went to test the bike they tought him how to go but barley how to stop it and he was only waring a bicycle helmet he pulled the throtle right back it got up to about 40 mph across the feild before he managed to shut the throtle off but it was to late over the bank of the feild onto the road and face planted into the tarmac his hole side of his face was all cut and bleeding they had to go to hospital. people will never learn it is all well and good teaching him/her to make it go but what happened to teching them how to make the bugger stop
damn im out of breath no punctuation!
it weighs 93kg
it holds 5.5 liters of fuel
it is 327.8 cc
it has a 27mm carb
it has a motoplat ignition if that helps
and i think it runs on 3% synthetic oil or 4% mineral oil
does it look like thispicture link
a bit like tis bike then it is mine i apolagize for the picture quility and the spec in the picture aint the same as it is
rider: Michael Kean
bike: kona cinder cone
forks: DDG steel
seat: megamo uni seat modofied
cranks: middleburn RS-7 20t
bars: Megamo
stem: Megamo new concept
tyres: F- IRC el gato R- schwalbe space
brakes: F- shim.LX R-mag. silver
wheels: F- deore on X517 R- deore on D521cd
gearing:durace short cage rear mech 21-11 dura ace cassete sramm pc99 chain
off the web site click for the picture scroll down to michael's bikehttp://My Webpage
with the trials seats the posts are very skinny so you cant raise the seat but waht i did was i got an old seat post and cut it up so i had a tube then i got epoxy resin and slid the seat into the post tube let it dry and you have got a raiseable seat
im writing the post on behalf of a mate he has a 92 gas gas and his spark is getting realy week the gap on the plug is beeing made so small so that it can get a spark and me and him think it needs a new coil can they be replaced and if so where do you get one from and roughfly how much money will it cost also is it easy to fit
if it is a two stroke run it rich on oil and dont rev it to much just poodle around on it
if it is a four stroke i dont have a clue i think you just ride em
on my bike i have swapped from castrol mtx top pj1 clutch tunner the pj1 is alot thicker i havent put it in thebike incase it buggers something up i just want to know what difference it will make
if the rust has set in on your bike get a can of corosion x it will get rid of the rust well if it is not set in to much dont get it on the disks and it leaves it oiled up as well after you have wiped it off
bicycles are definnetly easier i use to do bike trials i did it for 4 years intill i sold the bike to get a moto trials bike i find the motrbike knakering it might just be because i am knew to the sport and i have not built up my muscles enough
your suppost to put some instant gasket on it to seal it bought a new one when i rebuilt the clutch with my dad my freind had a simaler problem he put a new clutch cover on and it all pised out
a bit of basal brush there stu or maby not! just dont but alpinestar no stops they leek water like a sive very comfy and supportive though but that is all i can give them and they only last about six months till they start to fall apart
mc, my bike is total stock apart from i have changed the grips and the tires for new ones
and charlie that is true it would wipe out the aftermarket parts industry it is just on some bikes you cant fit them on easily like on technos and on the year 2000 rev3 from what my freind said
if it doesn't have one dont put one on if it was suppost to have one it would have come with it and i have found on betas that you cant have one cause the space is to small and the tubes pinch
just buy a new set 30 quid approx for the set from bvm moto my mate snapped the braket off and ripped a chunk out of the frame where the bolt goes through
