| |
-
It will do things you don't expect, and the things you expect it to do, it won't. If you're riding purely for fun, then it won't dissapoint and the best bits are in between the sections.
-
Expect a big adjustment period, the 4rt will frustrate you to start with, but the grin on your face will more than make up for it.
-
If it's that hot then the only gear I'd like to wear would be shorts, t shirt and some trainers, but that wouldn't be very sensible, so stick to the proper attire, grin and bare it, drink plenty of fluids.
As for your trails, 1st, 2nd or 3rd will be fine, if it's sticky under the tyres, pull 3rd. Trials tyres don't tend to clean themselves out very well at low speeds, so a burst of speed now and again will help clean the treads.
-
I've snapped them all in the Scott, even when new. The only chain I will use now is the DID ERT2. Not cheap but worth every penny. The last one has done 2 Scotts.
-
Mine does this when its hot, really hot. Usually about 4 hrs into the Scott. When it has cooled down for a few minutes it will run fine again
-
Plug it, use multiple strips (dog turds) to plug larger holes. May leak a little or completely fix it.
-
A big enough hit on the sump guard will split the generator cover nearly in half and crack the right crankcase cover, not cheap to replace and not easy to weld. Won't be trying that section again!!!
-
Thanks chappo. Not much smooth riding, you must have seen my one and only good ride! At least the weather was good though!
-
Is it the PHBH carb? If the mixture screw is on the cylinder side of the carb it should be "in" to lean and "out" to richen. I think we used to run them at about 2.25 turns out, but that was on the PHBL carb.
When the screw is on the air box side, then it's as bilks described.
It's been around 13 years since I messed around with those carburettor thingys, so I could be wrong.
-
That's the correct iridium. It may be worth trying the 5 if it doesn't get to stretch it's legs very often. I'm using the std filler cap with an open tube to vent.
-
I'd take the aftermarket breather off and try without it.
The 4rt will soot plugs if it's not warmed up properly and the throttle blipped too much.
As far as I know NGK don't make a cr6eh9 iridium equivalent, they do a 7 and a 5.
I've been using the 7 iridium for a while, purely for the Scot as it tends to misfire when it's thrashed to within an inch of its life.
When we rode abroad for the Europeans the factory lads would give us cr5eh9's.
-
I don't know, I've had a quick search but can't find it. I'll try again
-
Some time ago there was a thread running about throttle bodies going past The lock stop, which was fixed by a simple washer. Perhaps you're unlucky enough to have broken 2.
-
How about the bank angle sensor?
Dodgy connection to the plug cap
-
Only when the s/arm had rubbed through the loom behind the engine.
bad earth?
-
They tick over at 1800rm, so I'm guessing they could pull more than 10k
-
I can't imagine how many hours it did. 4 ssdts and 6 scotts alone would put at least 120 hours on it. I'd practise 2 times a week for a year or so and I bet there weren't many weekends that I didn't ride from 2006-2009. The bike had oil and filters every 2 months ish, valves were checked and set every 6 months
-
If you are concerned I'd spend a bit of money now, rather than wait too long and have to spend alot of money. New piston, rings and pin £130 ish, barrell re coat £130, new valves, springs etc probably another 100. If it goes bang then you could be looking at 2k
My 2006 had alot of hard hours on it, including several ssdt's, scotts, french 4 days, reeth 3 days, it would have gone for longer but I welded an oil way up which helped kill it
-
Sledge hammer usually sorts it out...... Make sure you take it off the bike first.
-
They can be run dry, but a little grease helps keep the cack out. Its probably worth changing the alloy tensioner arm too, they can wear very badly and its likely to have chewed up the rubber orings too. Replace the lot and its goood for another 8.
The 315's (possibly up until 2004) used a steel tensioner arm which tended to last longer, which fits straight on.
-
-
Water does not tend to cause many problems with the 4rt, unless its drowned. As said before, the connectors are pretty well sealed. Check the earth under the ht coil and check for a spark. If no spark, link out the bank angle sensor and try again
-
It's probably the best trial I have ever done, loads of sunshine, cracking sections and no one takes themselves too seriously. Everyone's there to have fun
-
The linkage bearings are 15x21x12 from a bearing trader.
-
I certainly don't p*** around it! I push myself very, very hard and the bike to within inches of it's life. I agree reliability and finding a good pace to go at all day is the key. Plenty of bike time leading up to the event probably helps too. Before last years event I hadn't ridden since April, and it knocked the **** out of me.
Sounds like you are having a go dorian???
|
|
