| |
-
Come on ben MAN Up ,, A well setup 320 is the best four stroke going..
You need to at the top of your game to have a good days rideing on one...when its good its very very good,but when you let them boss you about,they bite....
-
I find the easy way to do the linkage bearing on a sherco, is to take out the top shock bolt first.
This allows the shock to drop enough to get the bottom bolt out..
Rest you can you can get at easy enough..
-
sure it wasn't one of these ????
Hebo tank
-
I did one of these last week on a sherco..
I put the yoke in the feezer overnight to get it really cold.
Then just before fitting i droped the bearing in boilling hot water for a couple of minutes.
The bearing fell into place easy..
Blew all the water off with a air line and regreesed with water proof greese.
Al went well for me..Hope it works for you two..
-
I've sean a couple of gas gas swingarms break but never a techno one..
It must be all the pies you eat...
Theres loads of second hand ones about,,, Eblag and like..
-
I have a ohlins fitted to my 08 320 and it is very good compared to the olle..
They give a very good feel and i find that they make the bike grip a lot better. Not to hard to setup, but its best to have the right C spanners..
You could try giving Robin Martin a ring at RCM motorcycles..(01209820896) Hes normally got a few second hand shocks in good order..May even have a Ohlins..
The 08 Olle can be rebuilt,, as for cost i seem to think it was around
-
-
I had a DID rear wheel built up that i use a my comp wheel and use the
original wheel for pactise..
As i recall it cost about
-
When you just can't think of any other thing to spend the best part of
-
Yes it will fit...
Bit of black paint on the clutch cover and water pump houseing,,,, Job done !!!
-
I had the same sort of thing when i first got my sherco 320...
I took 2 springs out of the clutch and rellay helped...sliped a bit in top gear but was very easy to ride in the sections..
-
Just wondering what other sherco 320 4t riders are running there Keihin carbs at..
I've got mine set at..
118 main jet
42 pilot jet
4 slide
jjh needle
3/4 turn out on air screw
Seems fairly good,but would like to know if it could be better...
-
Thats a good write up Dan..
I know what you mean about a better mechanic than rider...
-
I think its good news,,,,maybe gas gas have bought Lambkin in to ride its long awaited 4 stroke ..!!!
-
-
I'm with jimmy on this one......
-
You could try a fuel pump off a 2010 2011 sherco...
just an idear...
-
I'd be intersted in knowing how you are getting along with this and for what reason you are doing it for...
I have a spare keihin carb set up the same as the 08 spec on my bike,,but could be tempted to do the same as you are doing if there are good results to be had...
What was the cost of parts you needed and where did you get them from ..????
Cheers mike
-
Thanks guys for the heads up about the hurran trial,,
have you got any contact details for this ???
-
Are there any trials this weekend around the bristol area...
I'm coming up on saturday to do the steve saunders trials school and was hopeing to ride a trial on the sunday..
So if anyone knows of a good club trial within 50 miles of Bristol on the 21st then let us know...
Cheers mike
-
Best of luck with this one and hope you got some serious deep pockets...
would love to see some build photos if you do go ahead with it...
-
I would give them a call and check first.....
-
I've taken all three of the restrictors out of the girls lt50 and it runs so much better...
theres one in the carb on the poilot jet....one in the carb manifold....and one in the front part of the exhaust pipe...
run it up on choke for 30 seconds and then its fine alday..
-
Well its still hanging on the workshop wall...
Trying to find anyone that can weld tiaium down this way has been hard..
I've sent a email to S3 hopeing that they might be able to help..
But if anyone knows of someone that could help please let know...
Cheers Mike
-
Good write up there Neil ,, explains it very well...
|
|
