woody

Carb for the Jumbo was 28mm, never heard of 30mm fitted as OEM. For a non-reed engine the pilot is 50 and slide 60, needle X2 and needle jet AS272. The delorto should perform fine if it's not worn out There is quite a difference between the reed and non-reed motors in power delivery. I tried a non-reed back to back with my reed engine bike when I had one and the non-reed was pretty flat with slow pick up off idle/pilot before surging and getting lively when the revs came up. Are you mistaking that for lean jetting? The reed engine lit up instantly I've run Delorto and OKO back to back on my 340 Sherpa and can't fell any noticeable difference which makes me wonder if it is just the slow take up of the non-reed engine that is giving the impression of weak jetting below 1/4

Whether it fits depends on which Sherpa you have which you haven't mentioned. A Sherpa seat won't mate up to that tank very well, if at all

1972/73 Sherpa T 325cc

If you google ossa wiring diagram you will find one - the blue andblack are for the ignition to the coill, blue on the bigger spade terminal if you intend using the lights to ride the bike in the dark, a candle would be a better option. The combination of not seeing something until the last minute and poor brakes isn't something I'd like to tangle with.... Fit some mountain bike lights

You don't say which Amal, but assuming it's a concentric, for a C15 it should be a 22mm which is the diameter of the standard intake. Different bikes won't necessarily run the same on the same jetting so it always a bit of trial and error. There is only one needle for the four stroke concentric of that size which is U1. Problems at high revs could be either too weak or too rich, If it's too rich it can cause the bike to choke on full throttle, too weak and it will gasp/die. Main jet size is normally around 100 or 110. There should be no pilot jet, needle jet 105 / 106 and it must be the 4 stroke type with spray holes. The jet holder is longer in the 4 stroke so the main jet sits lower in the bowl. Slide is usually a 3 If it is a premier type carb the same settings apply apart from the pilot jet which is a different design to the normal concentric, screws into the outside of the carb body opposite the pilot air screw and this is usually the three ring jet There could be other reasons for it not pulling up a climb, timing, cam type, different head with big valves etc

Fantics weren't produced with reeds until the 5 series, last air-cooled monos, which was about '89

Easiest identifier at a glance on the slimline models is that the 250 had a round barrel with closely spaced fins, 350 had a square barrel with wider spaced fins Ebay, facebook marketplace as well as a number of Bultaco facebook groups where you can see items for sale or ask for wanted items In the UK, In Motion have the biggest stock of parts

Last of the 'slimline' models from 1975 250cc. Model number is 150. Fkywheel and front wheel should be easy enough to find, exhaust more difficult

If you mean the production Sherpa N and Matador, I don't know either that well but although the frames share the same basic design I'd say the Matador is more bulky with more bracketry and reinforcement. The Sherpa N looks more bare like the Sherpa T I forgot one word when I mentioned about 669 NHO being based on a Matador frame and that was 'probably' I guess it could just as easily be based on a Sherpa N, which, thinking about it, seems more likely. It is known that the frame number of NHO begins with a 4

Yes, not just works teams either. The first 5 speed model 27 he had used the same plate as a later 4 speed bike. The original 669 NHO wasn't a Sherpa T as such as the T didn't exist at the time, the frame was a modified Matador, which is how the original NHO frame can be identified, from the mods and welds

I've never seen anything that gives information as to specific serial numbers for V1 and V2. It seems plausible that 1 - 479 are V1 but I wouldn't know for sure. The chart also says '1er' model for both but I'd assume that means 1st version of the Sherpa T. No idea what the reference to USA and Spanish versions are, the serials numbers don't carry a suffix A or N on the bikes and I think most were sold to the UK anyway. The features of the frame are likely to be the best identifiers of V1 or V2

It was owned by a private individual for years then sold a few years ago, where to I don't know

That bike is a replica

The bashplate mountings are different, on V1 there are two U shaped 2 bolt brackets welded to the frame, one just in front of the bottom engine mount, the other just below the front engine mount. The V2 only has one midway between the two engine mounts. The V1 engine has a smaller diameter shaft on th ignition side of the crank and doesn't have a lighting coil. The V2 has the bigger crank, same as later bikes and has a lighting coil Carb, airbox, shocks are all the same, wheels I'm not sure, I've seen it mentioned that the V1 rear hub had a cush drive (mine doesn't) and that it came with chrome rims, V2 had alloy rims V2 is said to have the frame number on the headstock whereas earlier bikes had it low on the frame by footrest or higher on seat rail but I think this can be inconsistent, my V1 has the number on the headstock and it's a low-ish number. V1 had a black bottom yoke, V2 was silver Obviously with the bike being near 60 years old anything could have been changed or modified in that time though

Put a picture of the bike on here or one of the facebook groups as it's a lot easier to identify the actual bike itself than from a frame number

Unfortunately prefix 51 covers the 348 and entire 349 model range so without knowing which number range was used for which model you can't tell what it is from the number

It doesn't sit too badly if they are the 610mm stanchions as I'd expect it to be more raked, but to ride they need to be raised in the yokes, or they steer like a barge - you can see how much room there is between the bottom yoke and mudguard for 6" of travel I wonder if it has shortened damper rods to compensate for the longer stanchions. Bit of a mystery nonetheless. The fork bottoms are correct for that bike

Mine is an early bike so has the square tabs, wasn't sure about a different clutch on later 4 speed engines From your picture it looks as though there is something sitting between the casing and the basket. I can see the raised boss to the left but next to that is something else (immediately to the left of the basket teeth in the picture) what is that as it sits directly in the line with the crank sprocket, which is where the basket teeth should be You can tell straight away if the crank weight is in the wrong position as the tensioner wheel should be directly underneath the teeth, otherwise it would miss the chain

Yes that's a TR77 Verde, the number run begining 70 for the 250 isn't listed on the Ossa reference sheets The MAR had shorter forks up until 1976 when the MK3 was introduced with laid down shocks and forks which were about 2" longer and these forks were also fitted to TR77 and Gripper - 2" is about 52mm which ties in with the length of the different stanchions sold by In Motion which differ by 50mm. (The part number for the stanchions is the same for MK3 MAR and TR77) I don't know which model, if any, uses 610mm stanchions, maybe one of the motocross or enduro models Normally on the MK3 MAR, TR77 and Grippers, the forks are raised by about 2" through the yokes as they are too long and give the bike a stance like a chopper. In the photo yours looks to sit level even though the forks aren't raised. With stanchions 1" longer again you'd expect the bike to sit really high at the front, but maybe it's an illusion die to camera angle

Has the woodruff key been pushed backwards and is sitting partly up in its slot which is preventing the huib and basket fully locating. That basket is too far out, the outside edge should be somewhere near in line with the edge of the weight The only thing behind the hub should be the top hat spacer which locates in the seal You really need to pull the clutch off, remove the key and push the hub on to ensure it sits right up against the spacer Weights are generally interchangeable as long as the number of teeth and pitch is right as they differ on some models. I have a weight from a much later M158 engine on my M10 I'm not aware of any difference in clutches on M10 but someone else may know differently

They fitted a through shaft for the gear change in 1975 on the new M158/159 models, giving the option of a left hand gear change. To have the brake pedal on the right needed a cable to operate the brake but there was no provision on the frames to mount one so owners would have had to sort their own. In 1977 with the M198/199 model Bultaco released them from the factory with left hand gear change and right hand brake with cable - owners could still change to right hand gear change and left hand brake if they wanted to

For a full engine rebuild it will top £600 in parts plus cost of crank build and rebore. If it needs a primary chain you'll have to source one from outside UK as there are non here. The cycle parts will also add cost but it depends on how far you want to go in terms of finish - eg: you don't have to get frame repainted but to do it could be between £100 and £200 depending on finish, powder coat, sprayed, enamelled etc. Fork chrome, chrome in hubs, state of wheels, tyres, cables, bars. levers etc etc. You can easily be up to £1500 in rebuild costs depending on what needs doing and how far you go. Plus the cost of the actual bike unless you're being given it. If you're doping it to keep and use the cost doesn't really come into it but should you need to sell it on it's unlikely you'd get all of your outlay back. They have a ceiling in terms of what they're really worth. To buy a bike, there are loads of Sherpas for sale but the asking prices for many are way over value which is why most have been on sale for months and years, some people asking between £2-3000 for something really worth about £1000, sometimes less. Some of them look ok but when you actually examine closely, things like the tyres, shocks etc they aren't any use for trials riding, similarly the engine might run but need attention, hub linings, cables might all need attention, exhaust repacking, so more outlay on what's an overpriced ornament in the first place. There are decent bikes out there, you just have to be carefull in what you buy For registering, was it ever registered originally? If so there is a facebook page 'vin to reg' who will use the frame number to find the original reg number if there is one, if they do you then just apply for the V5 using a V62. If there is no trace you have to go through the new registration process and apply for an age related plate as a historic vehicle. Lots of info on this in the Road Legal forum

They were replacements for the slimline one piece fibreglass tank/seat unit. Fitted from 1973 - 75 in UK only due to fibreglass tanks being banned for road use

The M10 has the double weight as standard but these are interchangeable with the single weight as the fit on the crank is the same - as long as it has the same pitch and teeth number. Your problem looks to be the basket which is sitting too far out. There is a top hat spacer that sits in the oil seal on the mainshaft and the basket and hub sit up against the spacer and when fully home the sprockets line up. There looks to be something sititng behind the basket in your picture? Is the correct spacer fitted. It's easy to see if the front sprocket is aligned as the tensioner wheel should be in direct alignment with it

Nowhere if it's a complete kickstart you want. In Motion sell the knuckle but only for the coarse spline shaft. If you want a complete lever it's a case of looking for a used one - Telford show maybe or put a wanted post on the Vintage Ossa facebook group The modern day Dick Turpin in Spain, Frankie Mountain, has a new old stock Phantom klickstart if you'd like to part with £300 plus post.....