shercoman2k8 Posted February 13, 2009 Report Share Posted February 13, 2009 If any of you know could you please post upp the length and thread required for the bolts on an 06 sherco, probably the same upto present! Looking for; Clutch Cover, Flywheel Cover, Water Pump Housing, Clutch Master Cylinder, Fork Cross Brace, Yokes, Clutch master cylinder. Will I need to replace gaskets if the bolts are undone? the part will remain firmly in place as I will be doing one bolt at a time! Quote Link to comment Share on other sites More sharing options...
1oldbanjo Posted February 13, 2009 Report Share Posted February 13, 2009 Here is the link to the Sherco Parts Manual. You can look up the bolts/screws that you need. http://www.sherco.com/spare_parts.html You may not find a manual for your exact year - but most parts are the same. Quote Link to comment Share on other sites More sharing options...
shercoman2k8 Posted February 26, 2009 Author Report Share Posted February 26, 2009 (edited) Who said I was using alu? Just doing a hot spray on the heads so decided on new bolts.... if you heat them up really, really hot and spray them with your desired polyurea coating, (steel bolts this is) chuck them in the freezer over night then shove them in the bike! Cant even scratch them with a stanley knife! What kind of tit uses alu bolts in a high pressure area? Even titanium is a bit risky where you should have high tensile bolts! Edited February 26, 2009 by shercoman2k8 Quote Link to comment Share on other sites More sharing options...
Andy Posted February 26, 2009 Report Share Posted February 26, 2009 Just so you don't look like you're talking to yourself, user "sherco25016" had his posts deleted because they contained so much text talk they looked like another language. No text talk! Quote Link to comment Share on other sites More sharing options...
shercoman2k8 Posted February 27, 2009 Author Report Share Posted February 27, 2009 Oh right, I thought I was going insane for a minute then Quote Link to comment Share on other sites More sharing options...
bark Posted March 9, 2009 Report Share Posted March 9, 2009 Who said I was using alu? Hi, I'm new to the whole trials thing. I just picked up a beautiful 06 Sherco and I'm now basically clueless about what to do with it. Do I understand correctly from your post that the motor casing screws in these bikes are made from Aluminum? Or, did I understand that wrong? Thanks, Bark Quote Link to comment Share on other sites More sharing options...
copemech Posted March 10, 2009 Report Share Posted March 10, 2009 (edited) Hi,I'm new to the whole trials thing. I just picked up a beautiful 06 Sherco and I'm now basically clueless about what to do with it. Do I understand correctly from your post that the motor casing screws in these bikes are made from Aluminum? Or, did I understand that wrong? Thanks, Bark No, the factory bolts are cadmium plated steel. They will corrode a bit over time, yet are cheap to replace. The biggest potential problem comes not from appearance, but the corrosion on the thread portion due to water exposure. Treatment with a grease/ antisieze mix on all the threaded bolts you can access(not brake disc bolts) is advisable, although I usually replace all my common bolts with stainless steel and coat as stated. Coat axles with waterproof grease. Edited March 10, 2009 by copemech Quote Link to comment Share on other sites More sharing options...
bark Posted March 10, 2009 Report Share Posted March 10, 2009 Thanks, I was thinking 'Aluminum?!' Stainless sounds like the way to go for sure if I need to replace anything. Cheers, Bark Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.