brian r Posted August 10, 2009 Report Share Posted August 10, 2009 Hi folks, Playing with a 250 barn project. It actually starts and runs. However, it doesn't idle. Seems like I need to screw in the idle adjustment but it's already in all the way. Any thoughts? Quote Link to comment Share on other sites More sharing options...
max1956bikes Posted August 10, 2009 Report Share Posted August 10, 2009 carb needs cleaning Quote Link to comment Share on other sites More sharing options...
brian r Posted August 10, 2009 Author Report Share Posted August 10, 2009 OK, cleaned it once, but I'll do it again. I even used my ultrasonic cleaner, but I've seen that happen before. Thanks Quote Link to comment Share on other sites More sharing options...
max1956bikes Posted August 11, 2009 Report Share Posted August 11, 2009 sounds like you have cleaned carb well.take out air screw i use wd40 with red pipe on to make sure it comes out in 2 places.through pilot jet and small hole back of slide. also points set at 12 thou.also if it smokes may be piston rings sticking.or air leak on inlet manifold. Quote Link to comment Share on other sites More sharing options...
trial pat Posted August 11, 2009 Report Share Posted August 11, 2009 if it is a Honda TL 250 4 stroke 1975/76, then it is important that the ignition is set properly: distance of the breaker 3-4mm, check timing with a stroboscopic flash, check, that the mechanical advancer works. Mine had something in the exhaust, be sure, exhaust can breath freely Do you mean idling at low revs or it does not turn in high revs? Good luck from a Swiss Patrick Quote Link to comment Share on other sites More sharing options...
brian r Posted August 11, 2009 Author Report Share Posted August 11, 2009 Hi Pat, It revs fine, it just won't sit and idle and needs constant blipping of the throttle. It's close but no cigar. I'll pull the carb again. I need to pull the 125 carb and clean it anyhow. I need to play with the Beta carb too. Maybe I'll have one big carb playing day! Quote Link to comment Share on other sites More sharing options...
brian r Posted April 6, 2010 Author Report Share Posted April 6, 2010 Spring is here and I got the 250 to start and run fine. It was a pin hole in the float, replaced the float and problem solved. Quote Link to comment Share on other sites More sharing options...
trial pat Posted April 18, 2010 Report Share Posted April 18, 2010 (edited) Hy HondaTrials I fitted an Oko 24mm carb with power jet (deactivated) today, bought at ebay from Taiwan. Fits the inlet rubber, but to the airbox I found an old Montesa rubber (49mm instead of 42). After some trial and errors, the engine works quite well now. Slow jet 38 (like Keihin original) and main 112. I had to hang the needle at top clip (leanest) position. It starts easily and pulls at low revs. On the first street test, it is quite good, but not reving totally high, but pulls quite strongly now til 4/5 gas. I started with a 115, then 120, then 110, now 112 main jet. Trial test to follow soon. Does your TL rev up like a cross engine? or is there kind of a limit ? Regards Patrick Edited April 18, 2010 by Trial Pat Quote Link to comment Share on other sites More sharing options...
n714ag Posted May 7, 2010 Report Share Posted May 7, 2010 My TL250 has stock carb, retarded ignition timing and will continue to rev until the valves start to float! Quote Link to comment Share on other sites More sharing options...
brian r Posted May 7, 2010 Author Report Share Posted May 7, 2010 Hey Murray, How's it going. Is that the TMI frame? Quote Link to comment Share on other sites More sharing options...
n714ag Posted May 7, 2010 Report Share Posted May 7, 2010 Yea it is...got it back from Bob last summer...I've ridden it in three events so far...sweet... M Quote Link to comment Share on other sites More sharing options...
brian r Posted May 7, 2010 Author Report Share Posted May 7, 2010 Looking good. Lets hope we make it out a little more this year..... Quote Link to comment Share on other sites More sharing options...
axulsuv Posted May 12, 2010 Report Share Posted May 12, 2010 Brian ; The TMI looks better in person , It even keeps a smile on Murray's face non-stop when he's on it ! Glenn Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.