paynts01 Posted June 25, 2013 Author Report Share Posted June 25, 2013 Hi Nigel, The bike is new to me 2002 txt pro. Cured the air leak by seating airbox properly on the carb. What is a banjo filter as i dont recall seeing anything when i had the carb apart ?. Been out to bike today and was wondering if my fuel tank overflow pipe was blocked ?. When checking this i found it had a one way valve fitted to the pipe and am not sure if it was on the right way round. Are these standard ? (small plastic valve which when you blow down it air will only go in one way). Not part of the cap but connected to overflow pipe. Dropped the oil and it looked like choclate milk shake. On my first ride out on the bike a couple weeks ago it overheated and was steaming like mad. I took the tank off and found the fan wire disconnected and reconected it. Has caused a further problem, Head gasket or something. Cheers Paynts Quote Link to comment Share on other sites More sharing options...
thats_a_five Posted June 26, 2013 Report Share Posted June 26, 2013 MIlkshake oil means you have coolant in the gearbox. The oil seal on the water pump is a common problem on Gassers. Coolant in the gearbox will make the clutch drag very badly. That is a different problem from the stalling. The symptoms you describe sound like a plugged idle circuit. Make sure it is clean, clean, clean. The tiny holes can plug very easily. I use a tip cleaner for an acetylene torch and good solvent to clean them, then blow out with compressed air. Let us know what you find. 1 Quote Link to comment Share on other sites More sharing options...
paynts01 Posted June 26, 2013 Author Report Share Posted June 26, 2013 Would it be possible for water to get in from a missing kickstart shaft support bearing ? (ie) the one behind the carb. I noticed this bearing was missing after my first ride whilst cleaning the bike, i have now replaced it with a new one. Quote Link to comment Share on other sites More sharing options...
b40rt Posted June 26, 2013 Report Share Posted June 26, 2013 Would it be possible for water to get in from a missing kickstart shaft support bearing ? (ie) the one behind the carb. I noticed this bearing was missing after my first ride whilst cleaning the bike, i have now replaced it with a new one. Are you loosing coolant, water pump seal. If not, do you use a high pressure washer ? Quote Link to comment Share on other sites More sharing options...
paynts01 Posted June 26, 2013 Author Report Share Posted June 26, 2013 Have not had the tank of yet to check coolant. Yes i use a pressure washer and gave the carb a good blasting last time as i was going to take it off to strip and clean. Quote Link to comment Share on other sites More sharing options...
thats_a_five Posted June 27, 2013 Report Share Posted June 27, 2013 Yes it is possible that the water got in when you pressure washed it. When it overheated, the pressure in the cooling system may have pushed water into the gearbox. Either way, get the milkshake out and refill with lubricant. Quote Link to comment Share on other sites More sharing options...
paynts01 Posted June 27, 2013 Author Report Share Posted June 27, 2013 Just checked and it says 375 ml of oil ??? doesnt seem much. Quote Link to comment Share on other sites More sharing options...
jandyb Posted June 27, 2013 Report Share Posted June 27, 2013 Just checked and it says 375 ml of oil ??? doesnt seem much. Actually the first PRO (2002) had smaller engine casings. I think the amount of gear oil was 330 ml that year. -Jan Quote Link to comment Share on other sites More sharing options...
nigel dabster Posted June 28, 2013 Report Share Posted June 28, 2013 If the airbox is leaking dirt can get in. My guess is engine is worn and it needs a refresh. Carb has 10mm bolt on side this is banjo filter. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.