drca Posted September 18, 2016 Report Share Posted September 18, 2016 I took my TXT Pro apart to get the broken frame tab welded, and I'd like to see if I can clean up the spaghetti mess that's the current wiring. I searched around and couldn't find a wiring diagram for the bike. Does anyone have one or can point me to where I can find something useful? Thanks. DC Quote Link to comment Share on other sites More sharing options...
lineaway Posted September 18, 2016 Report Share Posted September 18, 2016 If it runs it`s not a mess. The `new` company made the owner of the only site that had a diagram remove it. Good luck. Quote Link to comment Share on other sites More sharing options...
drca Posted September 18, 2016 Author Report Share Posted September 18, 2016 If it runs it`s not a mess. It works... And believe me it's actually much better looking than my Scorpa (which is so bad that I can barely put the gas tank back on if I touch any of the electrical!). But I'd still like to understand what goes where (for example there is a weird loop on the connector to the ECU...) and find where to plug in some lights. The `new` company made the owner of the only site that had a dagram remove it. Good luck. So best is to contact Jim? DC Quote Link to comment Share on other sites More sharing options...
drca Posted September 19, 2016 Author Report Share Posted September 19, 2016 Found it (well, close enough!). One question tho: does the two ignition map work on these? Txs Quote Link to comment Share on other sites More sharing options...
grog Posted September 20, 2021 Report Share Posted September 20, 2021 (edited) Just brought a 2004 gas gas txt pro 125 and found it dose not have a kill switch dose any one know which wires it need to connect to fit one Edited September 20, 2021 by grog Quote Link to comment Share on other sites More sharing options...
ThinkVision13 Posted November 3, 2023 Report Share Posted November 3, 2023 On 9/19/2016 at 11:08 PM, drca said: Found it (well, close enough!). One question tho: does the two ignition map work on these? Txs After many years of driving, I also had a problem with the engine shutting down, after approx. 10 to 20 minute ride on my 2009 GG280 TXT. I Couldn't restart engine while warm. There was no spark on the spark plug. When I replace it, the engine runs for about the same time, then it shuts down on its own. I replace the ignition coil with a spare one, the spark plug still has no spark. Then I happen to find your wiring diagram and check the resistances on the ICM connector and notice the problem that the resistance on the BLK/RED wires is 0 Ohm instead of 20.9 Ohm. Both other resistances were very close to the prescribed ones. Member drca, I thank you for providing this schematic because it allowed me to get a quick diagnosis. Quote Link to comment Share on other sites More sharing options...
drca Posted November 4, 2023 Author Report Share Posted November 4, 2023 On 11/3/2023 at 12:19 PM, ThinkVision13 said: After many years of driving, I also had a problem with the engine shutting down, after approx. 10 to 20 minute ride on my 2009 GG280 TXT. I Couldn't restart engine while warm. There was no spark on the spark plug. When I replace it, the engine runs for about the same time, then it shuts down on its own. I replace the ignition coil with a spare one, the spark plug still has no spark. Then I happen to find your wiring diagram and check the resistances on the ICM connector and notice the problem that the resistance on the BLK/RED wires is 0 Ohm instead of 20.9 Ohm. Both other resistances were very close to the prescribed ones. Member drca, I thank you for providing this schematic because it allowed me to get a quick diagnosis. Happy this helped someone. Happy trails. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.