Bunge Posted March 28, 2017 Report Share Posted March 28, 2017 (edited) Evening all. I purchased the above bike as a fixer up'er/ hobby. The final thing to do before I can start riding it is attach the carb to the airbox correctly. When the two are joined the carb doesn't sit flush into the airbox rubber, even if i do the jubilee clip up tight, it holds it whilst the bike sits on the stand, but not well enough to hold and ride, and shake around. The carb nipple on the bottom has even started to wear away at the top of the engine casing. Anyone have an idea of how to remedy? I have thought about using a turbo tube of a vehicle, this will do the job, but I would rather complete the task properly rather than a temp bodge. Edited March 28, 2017 by Bunge spelling mistake Quote Link to comment Share on other sites More sharing options...
waynerobshaw Posted March 28, 2017 Report Share Posted March 28, 2017 Assuming its running a Delorto carb, there should be a rubber ring adapter on the carb-to-airbox side: http://www.splatshop.co.uk/gasgas-pro-dellorto-phbl26-adaptor.html Is that present? The carb is close to the engine casing but it shouldn't touch. Also, when refitting the carb and air box, i uses the following procedure: Slacken the engine/carb jubilee clip. Offer up the airbox to the carb and if need be, pull the carb out of the engine side to aid entry to the airbox (if necessary, warm up the airbox rubber with a heat gun to soften it) Once the carb is inserted properly into the airbox, push the airbox and carb back into the engine. Locate the 4 bolts holding on the seat/airbox. Re-align carb if the angle has moved. Tighten both jubilee clips Tighten the 4 airbox screws. Cheers, Wayne. Quote Link to comment Share on other sites More sharing options...
Bunge Posted March 28, 2017 Author Report Share Posted March 28, 2017 Thank you for your response and time Wayne. Yes the rubber is present. I will try your procedure and see how I get on. Attached is the photos I just took- the bottom one shows the nipple that is hitting the engine. sorry for the poor pictures- it shows the current gap, and after a few mins of riding the gap at the bottom is 2mm+, allowing dirty air into the carb. Quote Link to comment Share on other sites More sharing options...
arnoux Posted March 29, 2017 Report Share Posted March 29, 2017 Pretty common on those early 2002 bikes for that rubber tube to "shrink" a bit over time. Gets stiff and smaller! Gas Gas used a new part in 2003 Hence the BT280"3" 28017 part number Either fit a new airbox rubber tube # BT280328017, or like you said get something to extend the original. Quote Link to comment Share on other sites More sharing options...
waynerobshaw Posted March 29, 2017 Report Share Posted March 29, 2017 If you follow my procedure above together with warming up the airbox connection, i'm sure you'll find the carb will connect better. Also, make sure that the carb is fully pushed into the airbox even if this means you're having to pull it out of the engine side a little. Quote Link to comment Share on other sites More sharing options...
Bunge Posted March 30, 2017 Author Report Share Posted March 30, 2017 Thank you all for your comments. I heated up the air-box rubber and it became more malleable, and fits better. I will just try and source a thinner jubilee clip, as the one already on there is too wide. Thanks again. Quote Link to comment Share on other sites More sharing options...
Woody76 Posted March 27, 2018 Report Share Posted March 27, 2018 Hi all does anyone know where I cud source one of said rubber breather ducts for an 02 gassa txt pro 125cc bike plse. Have tried everywhere with no luck upto now. Just be available in the uk btw thanks in advance Quote Link to comment Share on other sites More sharing options...
Woody76 Posted March 31, 2018 Report Share Posted March 31, 2018 On 28/03/2018 at 12:33 AM, oni nou said: www.Trialstribulations.net £12.12p Listed in 'Induction' Thanks bud do u by any chance have a direct link to said item plse oni nou mate Quote Link to comment Share on other sites More sharing options...
zippy Posted April 1, 2018 Report Share Posted April 1, 2018 18 hours ago, Woody76 said: Thanks bud do u by any chance have a direct link to said item plse oni nou mate This may be what you are looking for: https://trialstribulations.net/index.php?main_page=product_info&cPath=26&products_id=2206&zenid=l0vmq58jonjciaok1s0plful96 Quote Link to comment Share on other sites More sharing options...
zippy Posted April 1, 2018 Report Share Posted April 1, 2018 On 3/28/2017 at 12:11 PM, Bunge said: Evening all. I purchased the above bike as a fixer up'er/ hobby. The final thing to do before I can start riding it is attach the carb to the airbox correctly. When the two are joined the carb doesn't sit flush into the airbox rubber, even if i do the jubilee clip up tight, it holds it whilst the bike sits on the stand, but not well enough to hold and ride, and shake around. The carb nipple on the bottom has even started to wear away at the top of the engine casing. Anyone have an idea of how to remedy? I have thought about using a turbo tube of a vehicle, this will do the job, but I would rather complete the task properly rather than a temp bodge. I installed one of these carb to airbox rubber adapters and made installation much easier and better to secure the airbox hose to the carb. It is also slightly longer than the OEM rubber adapter. http://www.vmar.com/carb.html Quote Link to comment Share on other sites More sharing options...
Woody76 Posted April 4, 2018 Report Share Posted April 4, 2018 On 01/04/2018 at 12:51 PM, zippy said: This may be what you are looking for: https://trialstribulations.net/index.php?main_page=product_info&cPath=26&products_id=2206&zenid=l0vmq58jonjciaok1s0plful96 That's exactly Wat I was looking for m8 part now fitted an bike back to normal thanks for all the help guys 1 Quote Link to comment Share on other sites More sharing options...
zippy Posted April 5, 2018 Report Share Posted April 5, 2018 20 hours ago, Woody76 said: That's exactly Wat I was looking for m8 part now fitted an bike back to normal thanks for all the help guys Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.