iconic558 Posted May 9, 2017 Report Share Posted May 9, 2017 (edited) Thought I'd post this here rather than Monty section as most t/s's run drums. Bloody odd this. Front brake creaks when applied when stationary and the lever feels spongy. The drum lining isn't split which was my first thought. Stripped the brake down and still does it...bit of a strange one? When moving the brake works ok but is still spongy. Any ideas welcome no matter how bizzare Edited May 11, 2017 by iconic558 Quote Link to comment Share on other sites More sharing options...
iconic558 Posted May 9, 2017 Author Report Share Posted May 9, 2017 (edited) PS I thought at one point that maybe the cable outer was collapsing, but noise originates from drum area. Edited May 9, 2017 by iconic558 Quote Link to comment Share on other sites More sharing options...
spen Posted May 9, 2017 Report Share Posted May 9, 2017 Are the linings 'tight' on the shoes? Is there any discernible movement or a gap between the linings and the shoes? Quote Link to comment Share on other sites More sharing options...
spen Posted May 9, 2017 Report Share Posted May 9, 2017 Try and force a feeler gauge between the lining and shoe and see if you can trap the gauge if it does go in by a bit of applied pressure. Quote Link to comment Share on other sites More sharing options...
paulmac Posted May 9, 2017 Report Share Posted May 9, 2017 Check the wheel bearings too. 1 Quote Link to comment Share on other sites More sharing options...
iconic558 Posted May 9, 2017 Author Report Share Posted May 9, 2017 Good ideas guys....the linings do have holes which i assumed were dust relief ports....for want of a better phrase, but they could indeed be riveted linings which could explain a lot. Wheel bearings seemed fine when checked earlier but good shout. Quote Link to comment Share on other sites More sharing options...
still trying Posted May 9, 2017 Report Share Posted May 9, 2017 My guess is something is flexing or moving under high load As you have looked into cracked drum,cable failure, shoe lining delamination, wheel bearings. that leaves; cam bush wear, Break shoe pivot peg might be flexing when loaded, the shoes may also be flexing, Is the shoe carrier plate lined up with the drum? (check it matches the drum really well when assembled. Have the breaks on hard before and during tightening the axle), Place a finger across the plate and drum, when applying the break , feel if there is any movement This would mean that the shoes are not parallel with the drum across the face is the cable arm ok, not cracked, flexing, etc? (starting to look at extreme stuff now). 1 Quote Link to comment Share on other sites More sharing options...
iconic558 Posted May 9, 2017 Author Report Share Posted May 9, 2017 cheers Quote Link to comment Share on other sites More sharing options...
feetupfun Posted May 10, 2017 Report Share Posted May 10, 2017 Brake cam to cam followers galling Brake shoe pivots galling Cable end galling in brake arm Cable end galling in lever One shoe contacting the drum before the other shoe Brake shoes being tilted due to worn/loose wheel bearings or angular axle misalignment Worn camshaft to backing plate fit causing camshaft to tilt What is really important is not that it makes a noise, but that whatever is making the noise may also be the source of the spongy feeling 2 Quote Link to comment Share on other sites More sharing options...
iconic558 Posted May 11, 2017 Author Report Share Posted May 11, 2017 Well I've seen it all now. Stripped the shoes off the back plate and found a metal packing piece under each shoe on the brake cam....not sitting very well and not sitting flat. Without the packing piece there was not enough adjustment left on the brake cable. Just delivered the wheel and brake to Charles Johnson in Norwich to get the shoes religned with decent trials compatible material with minimal clearance....I think its a Ferodo greenish high metal content material..... 571? 2 Quote Link to comment Share on other sites More sharing options...
iconic558 Posted May 11, 2017 Author Report Share Posted May 11, 2017 (edited) £30 per wheel...not bad as EBC road work compatible shoes are £25 and not made to fit. Edited May 11, 2017 by iconic558 Quote Link to comment Share on other sites More sharing options...
turbofurball Posted May 11, 2017 Report Share Posted May 11, 2017 So is there not a choice of replacement shoes for old Montys? Quote Link to comment Share on other sites More sharing options...
iconic558 Posted May 11, 2017 Author Report Share Posted May 11, 2017 (edited) Yes shoes are available but far better to get the shoes 'matched' to the drums. Also the off the peg shoes are usually road material that just happen to cross reference to to trials bikes. Edited May 11, 2017 by iconic558 1 Quote Link to comment Share on other sites More sharing options...
turbofurball Posted May 11, 2017 Report Share Posted May 11, 2017 Interesting, you learn something new every day! Quote Link to comment Share on other sites More sharing options...
iconic558 Posted May 12, 2017 Author Report Share Posted May 12, 2017 (edited) Picked the religned shoes today from Charles Johnson's...great service, usual turnaround is 3 days but I dropped them off yesterday afternoon and they were ready this morning as they knew I was needing the bike for a trial this Sunday. They as tight as on the drum too, not a lot of wiggle room. When I bought new shoes for my Speedy they had loads of slack from new. Mark, the guy I dealt with is as keen as mustard too and a just really nice guy to deal with. He was very patient with my rookie questions on religning shoes. Top Class service Edited May 12, 2017 by iconic558 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.