pre65bert Posted September 21, 2017 Report Share Posted September 21, 2017 I made a big, and looking expensive, mistake of buying a none running "project" the engine is basically scrap. Does anyone know of a good source for a replacement? Any help greatly received. Quote Link to comment Share on other sites More sharing options...
cleanorbust Posted September 21, 2017 Report Share Posted September 21, 2017 Not sure if you're in UK but dkoffroad.co.uk have a complete motor for sale. Not especially cheap but they're open to offers and the postage is free! Worth a chat with them maybe? Quote Link to comment Share on other sites More sharing options...
pre65bert Posted September 26, 2017 Author Report Share Posted September 26, 2017 Yes I'm in the UK, the DK ones seem the early type. I think the answer is going to be find a complete bike and continue the search! Quote Link to comment Share on other sites More sharing options...
jon v8 Posted September 27, 2017 Report Share Posted September 27, 2017 What is actually wrong with the engine ? They can be really knackered,but still repairable. The old banger I have currently runs an engine built of of 3 scrappers,I only used new piston rings and a couple of gaskets to put it together. The crankcases had been welded at least twice before I had to do more ! The selector drum for the gearbox has also had welded repairs. If you are going to bin your engine I'd be interested in it for more "stock". 1 Quote Link to comment Share on other sites More sharing options...
pre65bert Posted September 27, 2017 Author Report Share Posted September 27, 2017 The whole thing is rough. I had it running, but the bottom was noisy with a tuneful piston slap. The gears were stiff to enaage and jumped out of 2nd. When I started to take it apart I found the flywheel thread was stripped. Even with a Snap On pulley/slide hammer its not moving, I've been soaking the thread/keyway for days without any joy. I havent used excess heat as I'm trying to retain the flywheel, but it may need some serious heat. What I'll find beyond that is anyones guess. Quote Link to comment Share on other sites More sharing options...
jon v8 Posted September 28, 2017 Report Share Posted September 28, 2017 22 hours ago, pre65bert said: The whole thing is rough. I had it running, but the bottom was noisy with a tuneful piston slap. The gears were stiff to enaage and jumped out of 2nd. When I started to take it apart I found the flywheel thread was stripped. Even with a Snap On pulley/slide hammer its not moving, I've been soaking the thread/keyway for days without any joy. I havent used excess heat as I'm trying to retain the flywheel, but it may need some serious heat. What I'll find beyond that is anyones guess. I wouldn't panic too much,they aren't too expensive for bits, do you mean the LH thread for the puller is stripped, or the thread that holds the flywheel on ? A decent rebore and a piston isn't too bad ,plus a rod kit, mains,seals and gaskets should sort the engine side. The gearboxes suffer badly when the gear lever gets clouted,bending the shaft, cracking the crankcases and sometimes splitting out the pegs in the selector drum. Most, if not all is repairable and a set of clutch plates if needed will help. They are good motor's, if yours is as bad as the junk I rebuilt, then it will have done a whole heap of work and suffered enormous abuse. 3 Quote Link to comment Share on other sites More sharing options...
pre65bert Posted October 2, 2017 Author Report Share Posted October 2, 2017 Thanks for all the help, the tip about welding a nut worked to get the flywheel off, it snap a high tensile M12 bolt in the process! I'm going to pull it apart and see whats what. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.