greski Posted October 15, 2017 Report Share Posted October 15, 2017 Hi There / New to the Forum I have been searching the web for details on Pro Trials rider setups to see what You can do to modify or improve Your Trials bike / After searching all I can seem to find is a little information of Cabestany's Preference for an Enduro Clutch on his Sherco Factory 300 ST. I have noticed theres a Golden Cylinder attached to the Chain Side of Cabestany's bike in pictures from various Competitions / Does anyone know what this is ??? I thought it might have been a special Ohlin's external Oil Shock ? Any ideas Guys n Girls ?? Also if anyone has anything to Add to this Topic or has any Pro setup questions themselves please add and hopefully the community will help us mere mortals out Delighted to be a member / Hope to hear from You soon Quote Link to comment Share on other sites More sharing options...
dan williams Posted October 16, 2017 Report Share Posted October 16, 2017 As said above. It's all about the careful setup and few "trick" parts. 4-5 hours making sure your jetting is spot on is much more profitable than $1000 worth of titanium. Of course the problem with new riders is they don't know what is a good setup so they will crank their spring preload way up and run their tires too hard and crank their levers in too far and rotate their bars back... There is a wealth of knowledge on here about setup and it's well worth digging through old posts to find the tidbits of info. Just remember the setup of your bike has to fit you and has to work in the sections you'll be riding. A bike set up for trick riding and huge splatters is going to make life miserable for a novice doing slow turns over round rocks. 2 Quote Link to comment Share on other sites More sharing options...
nigel dabster Posted October 16, 2017 Report Share Posted October 16, 2017 The cylinder on the side is a reservoir for the rear shock, an ohlins engineer said its imposible to work properly without this, us mere mortals excluded. The clutches (until changed to diaphragm) on both Shercos and betas (similar design) were not up to the techniques of the WTC so from dougies time at Beta onwards you will see the works bikes often have different casings and therefore internals. Be careful what you wish for as I saw Cabbys fourstroke was tuned so much so it blew up in Sweeden in 08(?) in the warm up. Not quite sure how he even competed that day but thats another story of different rules for the Spanish I guess. Regardless as above if you have a current bike set up to perfection it will be far better than you unless youre Bou. 1 Quote Link to comment Share on other sites More sharing options...
hgas Posted October 16, 2017 Report Share Posted October 16, 2017 The list is endless , arnau farre's gasgas has some sort of strange cooling system fitted where as the coolant is fed through red tubes all over the machine , dabills bike has got the rear brake master cylinder back in the old position by the carb instead of the new integrated brake pedal design on the standard gasgas , raga used to run an electronic water pump on his old gasgas , the factory betas have first gear removed and various internal weights removed , like others have said us normal riders just wouldnt benefit from any of these things ,nice to know what they get up to though ? 1 Quote Link to comment Share on other sites More sharing options...
cascao Posted October 17, 2017 Report Share Posted October 17, 2017 Old ALP clutch master cylinder. Bigger shock PU bumper stops. Bigger carb float bow. Increased capacity radiator. Lead at bash plate to met FIM minimum weight 1 Quote Link to comment Share on other sites More sharing options...
nigel dabster Posted October 18, 2017 Report Share Posted October 18, 2017 Oh yes dont forget your lead then you will really have a works bike. 1 Quote Link to comment Share on other sites More sharing options...
cleanorbust Posted October 18, 2017 Report Share Posted October 18, 2017 I hear Honda are developing special lightweight lead for Bou's bike. 3 Quote Link to comment Share on other sites More sharing options...
greski Posted October 25, 2017 Author Report Share Posted October 25, 2017 To all the above Members / Thank You very much for all the knowledge , Fantastic to know all of the information ( and some serious information from Dabster , Dan ,Oni Nou, Cascao ,Hgas , ) You have provided and hope someone else can benefit , The setup is crucial , I've been on a few MX bikes over the years and after learning the difference between a balanced Suspension setup and properly jetted bike compared to ( standard factory settings ) are worlds apart sometimes , I will say though the 2017 Sherco 300 ST Factory settings seemed very good right out of the box , Front Forks needed a bit more Rebound but other than that everything feels great , , Any advice on the Rear Ohlins Shock Setup You guys ??? I weigh Just under 11 Stone , The front Forks seem to Travel almost all the way , But Dont know if the Rear Shock is as soft as it should be for my weight .. The Ohlins Manual I found Online is for an older Shock ..And Its not great Any tips would be greatly appreciated , Quote Link to comment Share on other sites More sharing options...
nigel dabster Posted October 25, 2017 Report Share Posted October 25, 2017 push down on the "seat" in the middle of the bike front and back should move in harmony. 1 Quote Link to comment Share on other sites More sharing options...
jimmyl Posted October 25, 2017 Report Share Posted October 25, 2017 I’m sure they had been arucles on here about sag and pre load etc. The ohlins instructions I had gave this info and required sag to be a % of travel etc. As dabster says both ends to be balanced. Quote Link to comment Share on other sites More sharing options...
klonheadd Posted November 5, 2017 Report Share Posted November 5, 2017 (edited) On 10/25/2017 at 3:42 AM, greski said: Any advice on the Rear Ohlins Shock Setup You guys ??? I weigh Just under 11 Stone , The front Forks seem to Travel almost all the way , But Dont know if the Rear Shock is as soft as it should be for my weight .. The Ohlins Manual I found Online is for an older Shock ..And Its not great Any tips would be greatly appreciated , You can find full setup instructions here http://www.splatshop.co.uk/ohlins-rear-shock-absorber.html Edited November 5, 2017 by klonheadd Quote Link to comment Share on other sites More sharing options...
hgas Posted November 5, 2017 Report Share Posted November 5, 2017 Sorry to hijack the thread a little bit but whilst we are talking about sag ,i fitted some aftermarket h and d racing linkage plates to my Montesa, they seemvto have taken all the sag out of the back end now because they are slightly bigger, do I need to wind the spring down a bit ? Quote Link to comment Share on other sites More sharing options...
jonnyc21 Posted November 5, 2017 Report Share Posted November 5, 2017 If you have little to no sag you will have a very harsh ride. Best to get that sorted out. Your suspension needs to work together front and rear at the same time if you push down on the center of the bike. Quote Link to comment Share on other sites More sharing options...
nigel dabster Posted November 22, 2017 Report Share Posted November 22, 2017 There's an echo in here... 1 Quote Link to comment Share on other sites More sharing options...
jonnyc21 Posted November 22, 2017 Report Share Posted November 22, 2017 1 hour ago, nigel dabster said: There's an echo in here... It's a compliment to your well stated truth! 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.