jonnyc21 Posted March 13, 2018 Report Share Posted March 13, 2018 (edited) 1 hour ago, Jeff mc said: Ok. May be worth checking then. I can't see them being that far off but I'll see. I guess it would be more of an issue if the clearance is not enough. That would mean the valves aren't closing fully wouldn't it. Both sides to tight or loose can see similar symptoms depending on what the clearance is and witch valve is in question. I don't remember off the top of my head what symptoms are directly connected to witch valve being in what condition but I have seen almost everything in the range on my old 74 beetle from tight to loose on both sides. Edited March 13, 2018 by jonnyc21 1 Quote Link to comment Share on other sites More sharing options...
jimmyl Posted March 13, 2018 Report Share Posted March 13, 2018 Would just do tank first - then try injector but never heard of one . 1 Quote Link to comment Share on other sites More sharing options...
jimmyl Posted March 13, 2018 Report Share Posted March 13, 2018 Failing fuel pump will alllow you to ridd on low revs but can’t cope with sudden or higher revs - but like a blocked jet . i found got worse with time / heat . if you stop bike it gets better fiir a while after. 1 Quote Link to comment Share on other sites More sharing options...
Jeff mc Posted March 13, 2018 Author Report Share Posted March 13, 2018 Thanks for the help. Quote Link to comment Share on other sites More sharing options...
cangy1000 Posted March 14, 2018 Report Share Posted March 14, 2018 Have you by any chance plugged the lighting exstention into the main loom? I did for MOT. It ran very similar to what you describe. 1 Quote Link to comment Share on other sites More sharing options...
Jeff mc Posted March 14, 2018 Author Report Share Posted March 14, 2018 I'm not sure if it has a plug for lights. I did find a 2pin socket with a red blank cover over it but though that would be for plugging a computer in to. No lights on it anyway. Thanks anyway though. Quote Link to comment Share on other sites More sharing options...
nigel dabster Posted March 15, 2018 Report Share Posted March 15, 2018 new plug? 1 Quote Link to comment Share on other sites More sharing options...
Jeff mc Posted March 15, 2018 Author Report Share Posted March 15, 2018 Done a while ago. Quote Link to comment Share on other sites More sharing options...
jonnyc21 Posted March 15, 2018 Report Share Posted March 15, 2018 Any luck yet? Or still have a few things to go over first? Quote Link to comment Share on other sites More sharing options...
Jeff mc Posted March 15, 2018 Author Report Share Posted March 15, 2018 Heading out to check valve clearances now. I may back them off a bit to the upper end of the tolerances to make sure. Quote Link to comment Share on other sites More sharing options...
Jeff mc Posted March 15, 2018 Author Report Share Posted March 15, 2018 Right.... wait for it... I think I've fixed my bike thanks to your brilliant help- all of you. Valve clearance was set a bit tight. Slackened to the max clearance. Put some Di electrical grease on the 32 pin connector. Put a 1mm shim on the max throttle stop in the throttle body. Fired it up and revved great. Flicked the 1mm shin off because I'd just used hot glue as temporary. This made the back fire come back. So. Tight valves weren't helping and perhaps I need a shim fixing permanently. Throttle position sensor is perhaps worn. Much better though and light at the end of the tunnel! 1 1 Quote Link to comment Share on other sites More sharing options...
jimmyl Posted March 16, 2018 Report Share Posted March 16, 2018 Not wanting to pick holes on a good news story but thought you had tried an alternative throttle body early on in your diagnosis . just my engineering brain trying to putt everything in its correct pigeon hole 1 Quote Link to comment Share on other sites More sharing options...
Jeff mc Posted March 16, 2018 Author Report Share Posted March 16, 2018 This is the new (second hand) theottlebody that I bought. I can only think that the position sensor in it is slightly worn too. I need to try my original one back on to fully see if it was the valves and Di electrical grease which worked. Like anything I should have changed one thing at a time but with limited time to tinker I changed as much as I could. I'll report back what I find though as it's stuff like this that will help others. ?? 2 1 Quote Link to comment Share on other sites More sharing options...
Jeff mc Posted March 17, 2018 Author Report Share Posted March 17, 2018 I tried the old throttle body back on and it was really poor. Bogging down at all revs when the throttle is opened quickly. So the newer throttle body is in now with a shim in and it seems really good. So possible causes contributing were valve clearance on the tight side, poor connection on the 32 pin ecu and also the injector connection- cured by Di electrical grease. Thanks. 1 Quote Link to comment Share on other sites More sharing options...
nigel dabster Posted March 19, 2018 Report Share Posted March 19, 2018 one thing at a time......... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.