netley Posted October 18, 2018 Report Share Posted October 18, 2018 Just drained this out of my Cota 349 as mentioned in a previous post. Should I pull the clutch cover off or just wash it out, refill and see? Cheers. Quote Link to comment Share on other sites More sharing options...
feetupfun Posted October 18, 2018 Report Share Posted October 18, 2018 Not a big deal. A common sight on a trials bike that has ridden a wet trial. I would just fill it with fresh oil. Next time you ride in water it will probably do it again. Sometimes wet oil affects the action of the clutch but if you didn't notice, then I guess yours doesn't get affected. Quote Link to comment Share on other sites More sharing options...
netley Posted October 18, 2018 Author Report Share Posted October 18, 2018 It hasn't really seen water apart from damp grass. I"m washing out with white spirit at the mo' 1 Quote Link to comment Share on other sites More sharing options...
feetupfun Posted October 18, 2018 Report Share Posted October 18, 2018 1 minute ago, netley said: It hasn't really seen water apart from damp grass. I"m washing out with white spirit at the mo' What did the gearbox oil look like? Quote Link to comment Share on other sites More sharing options...
netley Posted October 18, 2018 Author Report Share Posted October 18, 2018 Golden and lovely. Where would the vent be? Someone said it could be blocked which could have caused the bubbling from around the clutch arm when it first happened. Quote Link to comment Share on other sites More sharing options...
netley Posted October 19, 2018 Author Report Share Posted October 19, 2018 I've washed out with white spirit and refilled. Slightly milky seepage from gear and clutch lever shafts. Undid filler and it is under pressure. Where's the breather? Neil Quote Link to comment Share on other sites More sharing options...
netley Posted October 21, 2018 Author Report Share Posted October 21, 2018 I have driiled 2mm hole in the filler cap and let the engine cool. Started it and within a few second there was oil being pushed out. I put in 300 cc of oil when I changed the oil as per manual. I fear chank seal gone and pressurising the clutch side. Any pearls of wisdom? Quote Link to comment Share on other sites More sharing options...
feetupfun Posted October 21, 2018 Report Share Posted October 21, 2018 My 348 used to have a positive pressure inside the clutch casing. I was never sure that it was a crank seal causing it though because I cleared out the gearbox vent (which was blocked) at the same time that I changed the crank seals. Quote Link to comment Share on other sites More sharing options...
netley Posted October 21, 2018 Author Report Share Posted October 21, 2018 Ok. I'll look at the gearbox vent tomorrow. Cheers. Quote Link to comment Share on other sites More sharing options...
dr nosh Posted October 21, 2018 Report Share Posted October 21, 2018 I'm currently re-building a 248 and have made a new stub to fit into the gearbox breather location, to take 1/4" clear tube (can see if its blocked), and then run up into the bottom of the airbox (almost directly above). Made the same size stub to fit the magneto cover, and will run the clear tubing up and under the tank. Clutch case breather? Not sure about where this is located. 1 Quote Link to comment Share on other sites More sharing options...
turbofurball Posted October 22, 2018 Report Share Posted October 22, 2018 That's a smart idea! I've got clear silicone tubing kicking around, might look at redoing all the breathers with it ... at the mo I run them all down the right side of the frame, but I can't remember why Quote Link to comment Share on other sites More sharing options...
netley Posted October 23, 2018 Author Report Share Posted October 23, 2018 Had a short chat with the guys at InMotion who reckon it is the crank seals. Pulled everything off with remarkable ease. I love the design of the clutch assembly which came off in one piece. Need to get a puller for the gear on the crank in front of the seal. I'm hoping my local bike shop MY Motors will have some of the parts on the shelf as Melroy used to ride these things competitvely back in the day. Quote Link to comment Share on other sites More sharing options...
feetupfun Posted October 23, 2018 Report Share Posted October 23, 2018 2 hours ago, netley said: Had a short chat with the guys at InMotion who reckon it is the crank seals. Pulled everything off with remarkable ease. I will be interested to see if you still think it is easy to work on after you get the primary gear off 1 2 Quote Link to comment Share on other sites More sharing options...
netley Posted October 23, 2018 Author Report Share Posted October 23, 2018 3 hours ago, feetupfun said: I will be interested to see if you still think it is easy to work on after you get the primary gear off Well You will have the last laugh.... Any sage advice for this recalcitrant bugger? Quote Link to comment Share on other sites More sharing options...
feetupfun Posted October 23, 2018 Report Share Posted October 23, 2018 Make or find a puller that doesn't damage the gear teeth. The usual two or three arm puller will likely not be able to pull hard enough and will damage the teeth. A suitable puller will pull against the back side of the gear without touching the teeth and it will pull on the whole surface, to spread the load better. I made a tubular puller that is in two halves. There are discussion threads on this forum that cover this job in detail. I can do photos again if the thread has disappeared. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.