Kdtx240 Posted September 12, 2020 Author Report Share Posted September 12, 2020 Hello everyone Today I started up the tx 240 for the very first time she pinged into life after turning the air screw about 1.5 turns out and idled just fine what a beautiful lazy engine in comparison to my bonkers kx125 and all those horrid chainsaws I have been fixing recently to make a bit extra. not much to report have to source a few parts mainly a clutch lever, bars, chain, and some kind of air filter. Does the clutch cable just attach to an arm of some type to push the clutch? Should there be a rubber to keep dirt out between the clutch cover and the cable . Or does the cable fit in and seal itself in. we can say there is one more aprilia tx about now. Thanks to the effort and skills of many people. Be safe everyone. Keep riding. Quote Link to comment Share on other sites More sharing options...
pschrauber Posted September 12, 2020 Report Share Posted September 12, 2020 Sounds good a photo would be nice, with the older clutch cover you need a clutch assembly with an mount to the case with an o-ring fitted. You get the cable from venhill or Mr. SWM. Quote Link to comment Share on other sites More sharing options...
Kdtx240 Posted September 15, 2020 Author Report Share Posted September 15, 2020 Yes I'm very happy with the results and progress I'm working at her this Saturday so I'll take a picture so the clutch assembly attaches to the case and unless you take it off on purpose it remains in place say even if you remove the side cover to work at the clutch , is that correct? And the cable connects to part number 7 is that correct? Quote Link to comment Share on other sites More sharing options...
Kdtx240 Posted September 18, 2020 Author Report Share Posted September 18, 2020 (edited) Update Got the clutch working Was unable to select a gear but the 2 shafts are turning free inside the gearbox It's either stuck in neutral or in a gear I think it's the shift mechanism causing the bother the gearbox is good on this one Hopefully take the side cover off and something might be obvious. Just a case of examining closer. Got new bars on and the clutch working so that's ok just the shifter mechanism. EDIT= I searched the internet and it's looking more like a case split job. Martinswm talks about a tensioner arm jamming behind the shift barrel and This seems the most likely thing. This would explain why it's in neutral. I can imagine such a thing from my kx125 build. Can I use the old crank seals or do I need new seals? I don't want them to fold over when removing the crank and shafts. When this is done she will run. Edited September 19, 2020 by Kdtx240 More information Quote Link to comment Share on other sites More sharing options...
Kdtx240 Posted September 23, 2020 Author Report Share Posted September 23, 2020 Just a quick update Have the cases starting to split. The front half is very tight and stubborn. It's starting to go but I'm not taking any chances. I've ordered a case splitter tool. There won't be much progress until this arrives. Flywheel put up a fierce battle too. Might be a fortnight yet. Quote Link to comment Share on other sites More sharing options...
Kdtx240 Posted January 11, 2021 Author Report Share Posted January 11, 2021 Hi all Got the engine sorted new kickstart arrived today slowly getting there Quote Link to comment Share on other sites More sharing options...
pschrauber Posted January 11, 2021 Report Share Posted January 11, 2021 Great, hopefully you can ride it again in the next time; always good to hear that old stuff got running again. Did you just got a new ambos or too the tiny spring and ball, then I recommend a very good allen bolt in high tensile steel, to fasten the ambos of the kick starter and a god stop washer, the fastening of the Rotax engine can be delicate. Quote Link to comment Share on other sites More sharing options...
Kdtx240 Posted May 15, 2021 Author Report Share Posted May 15, 2021 Hello After a full strip and rebuild i am having a problem The gears are selecting as I can hear them click and I checked them before continuing the engine however i have no drive. The clutch also wanted to move the bike forward when pulled in. It is almost as if the drive was not getting to the input shaft of the gearbox. New clutch plates were fitted and gears were all ok with no broken teeth or dogs. A bearing was replaced on the gearbox shaft. I cannot look at the bike until Monday evening. I would appreciate your input. Quote Link to comment Share on other sites More sharing options...
b40rt Posted May 15, 2021 Report Share Posted May 15, 2021 There are two plastic plugs on the clutch casing, remove the rear one and check the adjusted has slack, ie clutch isn't effectively engaged. Check there is also slack at the lever. Generally the issue with these engines is the clutch won't free off. What oil is in the gearbox ? Quote Link to comment Share on other sites More sharing options...
Kdtx240 Posted May 15, 2021 Author Report Share Posted May 15, 2021 So check if the little mechanism is not engaging the clutch through the plug, is that right? I had about 3\16 of slack at the lever or a coin width. 1000ml atf dextron in the gearbox Quote Link to comment Share on other sites More sharing options...
b40rt Posted May 15, 2021 Report Share Posted May 15, 2021 Correct, cable may be slack but mechanism still partly engaged. Atf is good, but check you have enough oil, there is a level screw in the casing behind the gear lever. From memory it's 1200ml. Quote Link to comment Share on other sites More sharing options...
Kdtx240 Posted May 16, 2021 Author Report Share Posted May 16, 2021 The level screw is approximately in the middle of the case- looking at it wouldn't suggest it holds the case on is that right? Is there a way of adjusting the clutch mechanism other than the cable? Quote Link to comment Share on other sites More sharing options...
b40rt Posted May 16, 2021 Report Share Posted May 16, 2021 11 hours ago, Kdtx240 said: The level screw is approximately in the middle of the case- looking at it wouldn't suggest it holds the case on is that right? Is there a way of adjusting the clutch mechanism other than the cable? Level screw is behind the gear lever as previously mentioned. Clutch adjusts behind plastic plug, take it out and you will see. Quote Link to comment Share on other sites More sharing options...
Kdtx240 Posted May 18, 2021 Author Report Share Posted May 18, 2021 Thanks that worked it was found the clutch was continuously engaged as advised. took the bike a quick spin as the evening was coming to an end and it seems quite acceptable Hopefully have all the gears, definitely 123 The front shocks need redone, with corrosion of the chrome causing the seals to fail. How can this be fixed? Quote Link to comment Share on other sites More sharing options...
Kdtx240 Posted July 29, 2022 Author Report Share Posted July 29, 2022 hello The bike bogs down after quarter throttle and creates a lot of smoke under load. It starts and idles fine and will start first kick when hot, 2/3 kicks on choke cold, and if its lay up for a month it will need a spray of starting fluid but always starts I have tried to adjust the fuel screw and needle height and even replaced the needle for an X2 and needle jet for i think av266 or As266 engine revs crisp in neutral, I had thought it was running good and was surprised when it bogged so badly starting to think it could be the condenser but my only reason to back this is a post I read about a users bike "4 Stroking" and bogging they replaced the condenser and problem solved. I do have a good spark it can be seen and heard. Another user posted how to mount the new condenser under the tank. Does the flywheel have to come off to fit? I don't want to start accumulating carb jets and I feel the timing is ok as there is no detonation I used the bike to feed sheep all winter due to the low gears and I didn't rev the engine so just got by this way. now I need the revs to round up the sheep. the plug is a rich condition oily petrol mix black. the airbox is missing a basic filter is mounted but this would mean more air and possibly a lean condition so its not that. please advise easiest or best way to mount new condenser or suggestions welcome best regards KD Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.