thall1 Posted May 24, 2020 Report Share Posted May 24, 2020 After six months Mine turned out to be an intermittent ecu fault... borrow one if you can and try it Quote Link to comment Share on other sites More sharing options...
volcano island trial Posted May 24, 2020 Report Share Posted May 24, 2020 Jonnyc21, I have a question, when you check for spark, do you have to have all electrical components installed ?..I have been kicking the kick start without the fuel tank installed, means the fuel pump is electrically disconnected...Also how does a working fuel pump soumd when connected to a 12 V source ?..does it whir for while then stop ? Quote Link to comment Share on other sites More sharing options...
jrsunt Posted May 24, 2020 Report Share Posted May 24, 2020 The bike won't spark without the fuel pump connected into the loom. 1 Quote Link to comment Share on other sites More sharing options...
jonnyc21 Posted May 25, 2020 Report Share Posted May 25, 2020 (edited) 17 hours ago, volcano island trial said: Jonnyc21, I have a question, when you check for spark, do you have to have all electrical components installed ?..I have been kicking the kick start without the fuel tank installed, means the fuel pump is electrically disconnected...Also how does a working fuel pump soumd when connected to a 12 V source ?..does it whir for while then stop ? jrsunt is correct, it will not start without it connected. Once when I cleaned my tank filter on my 07 4RT I didn't connect the fuel pump back up by mistake, took me a few min to figure out why it wouldn't give me spark. As for 12v on the pump you should be able to hear it kick on and off as long as you don't have to much background noise. They are fairly quiet so be sure there isn't much to distract when testing. Edited May 25, 2020 by jonnyc21 Quote Link to comment Share on other sites More sharing options...
54tphill Posted August 16, 2020 Author Report Share Posted August 16, 2020 On 5/24/2020 at 12:24 PM, thall1 said: After six months Mine turned out to be an intermittent ecu fault... borrow one if you can and try it My bikes playing up again, rode it 2/3 times for 3 hours a ride, now it’s started stalling/cutting out again, this thread was originally about my bike. I’m thinking maybe my ecu is faulty, everyone kept saying about the idle so I did fit an Apico hour meter/rev counter but with lock down the bike wasn’t used for a while. everyone was saying the rpm needs to be 1800, I fitted the Rev counter after I had tweaked it, the rpm only shows 1270 but it’s loud, like it’s reading it wrong ? It’s been fitted exactly how the instructions say. If I turn it up it’ll get to 1500 then cut out, turn it down to 900 and it’ll cut out, at 1200 ish it runs ok but occasionally tries to cough, the revs dip randomly. Sometimes I’m riding through a section and it’ll just cut out. I must have bought the most unreliable 4rt in England. ..... Quote Link to comment Share on other sites More sharing options...
thall1 Posted August 16, 2020 Report Share Posted August 16, 2020 Have you actually tried setting at 1800?... it is quite loud... very similar to a petrol lawnmower! Quote Link to comment Share on other sites More sharing options...
54tphill Posted August 16, 2020 Author Report Share Posted August 16, 2020 33 minutes ago, thall1 said: Have you actually tried setting at 1800?... it is quite loud... very similar to a petrol lawnmower! Yes i can Not get it to 1800, at 1500 it sounds like it’s going to ride off on its own but then it cuts out hence it must be wrong! Quote Link to comment Share on other sites More sharing options...
jimmyl Posted August 17, 2020 Report Share Posted August 17, 2020 Just been back through your posts You said a lanyard fitted just before you bought it - is it a genuine mont one? Maybe fit a kill button for a while instead Did you check how the bank angle sensor had been linked out ? cheers 1 Quote Link to comment Share on other sites More sharing options...
on it Posted August 17, 2020 Report Share Posted August 17, 2020 (edited) 21 hours ago, 54tphill said: Yes i can Not get it to 1800, at 1500 it sounds like it’s going to ride off on its own but then it cuts out hence it must be wrong! what maps are on the bike ? is all the restricts removed ?how is the bike running before cutting out black smoke miss fire ? if bike running good and only cuts out and bad to start when hot i think the problem is the cooling fan, starting to seize will turn /work but drawing to much current away from fuel pump also look at fan relay,i find it very strange the ecu will not allow you to set the correct tick over as its only a air valve screw Edited August 17, 2020 by on it add 1 Quote Link to comment Share on other sites More sharing options...
54tphill Posted August 17, 2020 Author Report Share Posted August 17, 2020 2 hours ago, jimmyl said: Just been back through your posts You said a lanyard fitted just before you bought it - is it a genuine mont one? Maybe fit a kill button for a while instead Did you check how the bank angle sensor had been linked out ? cheers Inch perfect fitted a apico lanyard for me when I bought it new, they also linked out the bank angle sensor so I’d of thought we could rule those areas out ? Quote Link to comment Share on other sites More sharing options...
lineaway Posted August 17, 2020 Report Share Posted August 17, 2020 After all this, have you tried running the bike with the gas cap off? It could not be venting properly. Every trials bike seemed to have venting problems in 2018 for various reasons. 1 Quote Link to comment Share on other sites More sharing options...
54tphill Posted August 17, 2020 Author Report Share Posted August 17, 2020 26 minutes ago, lineaway said: After all this, have you tried running the bike with the gas cap off? It could not be venting properly. Every trials bike seemed to have venting problems in 2018 for various reasons. That’s an interesting idea, it did actually start playing up after I fuelled up, so you think the cap on the top of the tank could be causing an issue ? Quote Link to comment Share on other sites More sharing options...
lineaway Posted August 17, 2020 Report Share Posted August 17, 2020 All these no spill caps just are terrible. 1 Quote Link to comment Share on other sites More sharing options...
jimmyl Posted August 17, 2020 Report Share Posted August 17, 2020 2 hours ago, 54tphill said: Inch perfect fitted a apico lanyard for me when I bought it new, they also linked out the bank angle sensor so I’d of thought we could rule those areas out ? You would like to think so but as you are still having issues would double check just to be 100% 2 Quote Link to comment Share on other sites More sharing options...
jonnyc21 Posted August 17, 2020 Report Share Posted August 17, 2020 (edited) I agree with lineaway to remove the no spill cap and see how things go. The two times I have tried one for any of my bikes I have had some kind of issue and ended up deciding not to do it again, no issues sense. And always worth a look at any changes that recently happened such as jummyl's suggestion on going back to a kill button to test. Edited August 17, 2020 by jonnyc21 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.