5again Posted January 27, 2006 Report Share Posted January 27, 2006 Trial last Sunday was a bit of a mudfest and would like to take the airbox completely off of my recently acquired s/h 05 rev3 to give it a good cleanup, used to do this on previous shercos - nice and easy to work on. Will the airbox assembly come off without removing the shock / exhaust? - or does either need to be removed first, it looks a bit tight in there, was even wondering if the expansion box needs to be slacked off or removed. Appreciate any guidance or previous experience. btw - I did remove the flywheel cover to let the leccy bits dry out, it did dribble a bit when removed. thanks again. Quote Link to comment Share on other sites More sharing options...
pa. Posted January 27, 2006 Report Share Posted January 27, 2006 I remove the muffler and loosen the centre section to reove the air box. I am sure some smart a*** will come back with a way to remove it through the air filter opening. Quote Link to comment Share on other sites More sharing options...
kinell Posted January 27, 2006 Report Share Posted January 27, 2006 Two options: - 1) Remove the silencer and middle pipe = 3 bolts 2) Remove the rear wheel = 1 big bolt Either of the above will give you enough room to get the airbox out and more importantly back in again. I always use option 1 as it makes fitting the rubber hose to the carb' much easier with the middle pipe out of the way. If you ride a lot of deep water I would recommend fitting a drain pipe to the air box (just in case!) Buy a valve stem (rear wheel). Drill a hole at the front and bottom of the airbox (same diameter as the threaded stem). Poke a straightened out wire coat hanger down into the airbox and out through the drilled hole. Thread the valve stem over the wire and wiggle it down until it pops out of the hole you just drilled. Fit the nut and then cut the threaded stem down to about half the original size (don't throw the offcut away). Unthread the nut to clear off any sharp burrs. Refit the nut and tighten it all up (no need to seal it but I suppose it wouldn't hurt to use some silicone) Fit a length of clear piping to the threaded stem. Thread it towards the front of the bike and down towards the back of the gear lever and let it hang in the sump guard area. Fit the threaded offcut into the end of the pipe and replace the dust cap. After each submarine expedition, simply glance at the clear pipe to see if any water has been collected. Remove the dust cap to drain and then refit Quote Link to comment Share on other sites More sharing options...
stuessenhigh Posted January 28, 2006 Report Share Posted January 28, 2006 mmm...neat idea Kinell Quote Link to comment Share on other sites More sharing options...
kinell Posted January 28, 2006 Report Share Posted January 28, 2006 There's no way that I could come up with something so simple and effective I'm afraid I sneaked into Silsden HQ and watched Griffo prepping the Team Beta bikes for last years SSDT - I'll try and post a piccy later... Quote Link to comment Share on other sites More sharing options...
kinell Posted January 28, 2006 Report Share Posted January 28, 2006 (edited) Pic 1 Edited January 28, 2006 by Kinell Quote Link to comment Share on other sites More sharing options...
kinell Posted January 28, 2006 Report Share Posted January 28, 2006 (edited) Pic 2 Edited January 28, 2006 by Kinell Quote Link to comment Share on other sites More sharing options...
totalshell Posted January 28, 2006 Report Share Posted January 28, 2006 Great idea/ solution and just the sort of thing that i would have thought Messers Lampkin, Birkett, Shirt and Rathmell would have been eager to share with thier customers or prospective customers via websites etc we're all eager to make the most of and get the best from our bikes so please guys don't keep these 'works' secret mod's a secret! Quote Link to comment Share on other sites More sharing options...
totalshell Posted January 28, 2006 Report Share Posted January 28, 2006 What do they say about acting in haste then repenting at leisure... http://www.ssdt.org/sitebody/modules/Uploa...klist%20PDF.pdf thanks Mr. L. and my apologies, job well done! Quote Link to comment Share on other sites More sharing options...
5again Posted February 4, 2006 Author Report Share Posted February 4, 2006 Thanks for the advice, I removed the wheel and silencer and loosened the centre section and it all came apart, though getting the airbox boot back on the carb when I put it back together was a pig! Thanks again! Quote Link to comment Share on other sites More sharing options...
stuessenhigh Posted February 5, 2006 Report Share Posted February 5, 2006 I'll have to go and have a look at my bike r2w..but I THOUGHT that, if you did it that way, it was impossible to tighten the jubilee clip..(the one at the rear of the concertina rubber)..((airbox end))... isnt it hidden behind the frame????? Hopefully you're right..which I'm sure you are...(as always!!!) ..but I'll go and have a butchers at me bike anyway Quote Link to comment Share on other sites More sharing options...
stuessenhigh Posted February 5, 2006 Report Share Posted February 5, 2006 thanks for posting the pics as well kinell... It'll give me some ideas for when I try to enter the SSDT...mind you, I'll probably be too old then, 'cause I',m waiting till I'm good enough..which might be a VERY long time!!!! Quote Link to comment Share on other sites More sharing options...
stuessenhigh Posted February 7, 2006 Report Share Posted February 7, 2006 Its definately behind the frame on mine, unless we're talking about a different clip Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.