trialsriderfeetup Posted May 21, 2020 Report Share Posted May 21, 2020 I have a sherco factory 2019 250 .my front brake is always cr.....p. how do I get it ready keen.tried all the bleeding, tapping the cable to get bubbles out.gaffer pads in.it just feels like I alway have to squeeze really hard,and with one finger. Though of the short leavers, haven't done that yet to get more leverage . Sanding the disc up a bit with sand paper.rough the pad up a bit. Disc look ok not polished up.. any ideas. .... chris Quote Link to comment Share on other sites More sharing options...
cascao Posted May 22, 2020 Report Share Posted May 22, 2020 Check if disc is bend. If not drive bike while holding brake. When hot, pour water in caliper area. Should work. 4 Quote Link to comment Share on other sites More sharing options...
lineaway Posted May 22, 2020 Report Share Posted May 22, 2020 Sounds like the pads have been contaminated. 2 Quote Link to comment Share on other sites More sharing options...
misscrabstick Posted May 23, 2020 Report Share Posted May 23, 2020 On 5/22/2020 at 12:13 AM, trialsriderfeetup said: I have a sherco factory 2019 250 .my front brake is always cr.....p. how do I get it ready keen.tried all the bleeding, tapping the cable to get bubbles out.gaffer pads in.it just feels like I alway have to squeeze really hard,and with one finger. Though of the short leavers, haven't done that yet to get more leverage . Sanding the disc up a bit with sand paper.rough the pad up a bit. Disc look ok not polished up.. any ideas. .... chris Shorter levers will give you less leverage depending on where you pull, the further from the pivot point the finger the more leverage you get but the lever will move further at the point of finger contact. Quote Link to comment Share on other sites More sharing options...
cascao Posted May 24, 2020 Report Share Posted May 24, 2020 Sherco had (or still have not sure) different levers from others with same model master cylinder. The pivot point in sherco give more leverage than others. So the lever should be specific for sherco's Quote Link to comment Share on other sites More sharing options...
trialsriderfeetup Posted May 24, 2020 Author Report Share Posted May 24, 2020 The short leaver thing that is so I don't have long leavers on when I don't need them,I would adjust the leaver so my finger was at the end of the short leaver.so more leverage as the pivert point is a lot ferther away ,when I use a standard leaver my finger is right on the bend not far past the pivert point .have tyred some one's bike with the short leavers on and pulling from the end of the leaver,it is a lot easier more leverage. Plus shorter leaver don't brake as easy. The idia of getting the pads really hot and dowsing with cold water rings a bell with me,think people have done that before could work.never tyred it ,but will next time I'm out having a practice , it's possible my pads are contaminated with wd40 as I spray with wd40 after washing to repell all water stops things rusting up.done it for years.thank you for all comments keep them coming any fresh ideas welcome. Chris. Quote Link to comment Share on other sites More sharing options...
huski Posted May 24, 2020 Report Share Posted May 24, 2020 Think the problem is WD 40 on the disc and pads.Fit new pads and clean the disc thoroughly with brake cleaner,the old pads will never be any good.The brakes on this bike should be very good after you do this Quote Link to comment Share on other sites More sharing options...
trialsriderfeetup Posted May 24, 2020 Author Report Share Posted May 24, 2020 Ok will change the pads.I have a new set .the pads in are the one's in from new as I don't ride as often as I us to. Age sindrom. In fact I never change them, usually get a new bike, anyway new pads it is. Might just try the water thing first.do we think this won't work?. Is carb cleaner as good as brake cleaner or is it the same stuff. Keep em coming. Quote Link to comment Share on other sites More sharing options...
cascao Posted May 25, 2020 Report Share Posted May 25, 2020 Be careful with WD40. All small particles you breathe will stay inside your lungs forever.... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.