Lee halsall Posted March 3, 2021 Report Share Posted March 3, 2021 The nipples in my Alpina are eaten away . can anyone tell me the thread size of the spokes ? I measure them at 3.37 mm dia , which corresponds with nothing I can find . Quote Link to comment Share on other sites More sharing options...
paulc76 Posted March 3, 2021 Report Share Posted March 3, 2021 Pretty sure they are cycle thread Quote Link to comment Share on other sites More sharing options...
petorius Posted March 3, 2021 Report Share Posted March 3, 2021 Pretty sure Bultaco spoke threads are metric, trying to find metric nipples will be a challenge. Quote Link to comment Share on other sites More sharing options...
feetupfun Posted March 4, 2021 Report Share Posted March 4, 2021 For many years I bought replacement aluminium Bultaco nipples from Bultaco parts people but I think that the remaining stocks of them have been used up by now. It seems a waste of the spokes not to reuse them because the stainless steel Bultaco spokes are/were very nice. For my most recent Bultaco restorations, I gave up looking for aluminium nipples and bought new stainless steel spoke kits, which are quite economical nowadays. 1 Quote Link to comment Share on other sites More sharing options...
teamferret Posted March 4, 2021 Report Share Posted March 4, 2021 Both central wheel and Talon did them at one time Quote Link to comment Share on other sites More sharing options...
djr Posted March 4, 2021 Report Share Posted March 4, 2021 If they are the same as on my Ossa MAR, then they are 3.5mm. On my bike the stainless spokes on both wheels were perfect , but the Alloy nipples were corroded and nobody seems to sell nipples in the size required I was reluctant to buy 2 x sets of stainless spokes { at £80 a wheel } I managed to find somewhere that sold nickel plated brass nipples of the right dimensions at a reasonable price , with just a pilot hole. then I got a 3.5mm thread tap and threaded all 72 nipples { yes this was tedious , but the money saved payed for some other parts } I cant remember where I got the nipples , it may have even been a cycle place ? 1 Quote Link to comment Share on other sites More sharing options...
Lee halsall Posted March 4, 2021 Author Report Share Posted March 4, 2021 (edited) My problem now is getting the alloy nipples off the spokes , managed to get three off ,the rest just break up leaving a big lump of alloy in the spoke hole . My nearest wheelbuilder tells me they are 8 gauge spokes and that only BMW have metric spokes . Think I’m going to just cut the spokes but it causes real anguish to cut such nice spokes . Edited March 4, 2021 by Lee halsall 1 Quote Link to comment Share on other sites More sharing options...
Lee halsall Posted March 4, 2021 Author Report Share Posted March 4, 2021 Finally bought a parts list from inmotion , and right enough djr , m3.5 spokes . doesn't help get the oxidised mess out of the spoke holes , but I know what the said mess used to be . Quote Link to comment Share on other sites More sharing options...
djr Posted March 4, 2021 Report Share Posted March 4, 2021 It should get easier ,with each nipple you remove the other spokes should get looser , which might mean you can get more room to get some grips on them and crush them / turn them I was lucky, on mine as they had all mostly turned to white powder - not much Aluminium left Quote Link to comment Share on other sites More sharing options...
lsv Posted March 4, 2021 Report Share Posted March 4, 2021 Contact Paul at Sids Wheels, he'll sort it for you. Top notch wheel builder................ Quote Link to comment Share on other sites More sharing options...
woody Posted March 4, 2021 Report Share Posted March 4, 2021 1 hour ago, lsv said: Contact Paul at Sids Wheels, he'll sort it for you. Top notch wheel builder................ He doesn't have the thread for Bultaco spokes, I've spoken to him about it, he's done a few Bultaco wheels for me Quote Link to comment Share on other sites More sharing options...
feetupfun Posted March 5, 2021 Report Share Posted March 5, 2021 10 hours ago, Lee halsall said: My problem now is getting the alloy nipples off the spokes , managed to get three off ,the rest just break up leaving a big lump of alloy in the spoke hole . My nearest wheelbuilder tells me they are 8 gauge spokes and that only BMW have metric spokes . Think I’m going to just cut the spokes but it causes real anguish to cut such nice spokes . Heat those nipples with a fine flame and they will fall apart. Any remnants of aluminium can be removed from the spokes by soaking the threaded end in a mild acid Quote Link to comment Share on other sites More sharing options...
feetupfun Posted March 5, 2021 Report Share Posted March 5, 2021 https://www.amazon.com.au/3-5mm-Metric-Right-Thread-0-6mm/dp/B07B4C9TH8 I haven't check the pitch of the Bultaco spokes yet but if they are 0.6mm then I'm thinking of getting some of these and some blank nipples 1 Quote Link to comment Share on other sites More sharing options...
pschrauber Posted March 5, 2021 Report Share Posted March 5, 2021 On 3/4/2021 at 10:22 AM, feetupfun said: For many years I bought replacement aluminium Bultaco nipples from Bultaco parts people but I think that the remaining stocks of them have been used up by now. It seems a waste of the spokes not to reuse them because the stainless steel Bultaco spokes are/were very nice. For my most recent Bultaco restorations, I gave up looking for aluminium nipples and bought new stainless steel spoke kits, which are quite economical nowadays. You can still get them, Stainless steel spokes and even with one buttend end and with aluminium nipples, Orlando Calonder in Buchs Switzerland is still manufacture them. He has made several batches of spokes and nipples zto my bikes , and of course with aluminium nipples and stainless steel spokes. You can save a good amount of weight with doing so and the properties of the aluminium and the stainless steel is flawless. Here the rear wheel with super light CZ Duraluminium/Magnesium hub and Acront rim: The front wheel even lighter, also CZ and Acront: And too as we are in the Bultaco section, Orlando Carlonder stainless steel spokes and aluminium nipples mounted to Bultaco Sherpa 199b hubs: I never had an issue so far with his spokes and also in terms of corrosion the wheel are trouble free. The website of Orlando: https://www.orlandocalondersa.com/product-Speichen und Felgen 2 1 Quote Link to comment Share on other sites More sharing options...
Lee halsall Posted March 5, 2021 Author Report Share Posted March 5, 2021 15 hours ago, feetupfun said: https://www.amazon.com.au/3-5mm-Metric-Right-Thread-0-6mm/dp/B07B4C9TH8 I haven't check the pitch of the Bultaco spokes yet but if they are 0.6mm then I'm thinking of getting some of these and some blank nipples Measured the thread this afternoon and the spokes are .6 mm pitch . Managed to get all the nipples off too , took a couple of hours with blowlamp and penetrating oil . 3 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.