duckwizard Posted February 17, 2004 Report Share Posted February 17, 2004 Can anyone advise on a method to seal a fiberglass fuel tank. Mine has split on the lower edge seam. Would a epoxy resin be suitable. Or can I just use the standard fiberglass resin / matt. Thanks in advance Quote Link to comment Share on other sites More sharing options...
hrc2002 Posted February 17, 2004 Report Share Posted February 17, 2004 Hey DW, There was a post about leaking takes a few weeks ago, and I think this covered repairing. Might be of some interest... Click Here Quote Link to comment Share on other sites More sharing options...
alan bechard Posted February 17, 2004 Report Share Posted February 17, 2004 Standard fiberglass resin and repair procedures should be fine. What bike has a glass tank? Quote Link to comment Share on other sites More sharing options...
duckwizard Posted February 18, 2004 Author Report Share Posted February 18, 2004 The bike is a Cagiva DG350. Is there not a sealer that i can use inside the tank, after the external crack is repaired. If i use fiberglass petrol would surely penetrate this. Quote Link to comment Share on other sites More sharing options...
alan bechard Posted February 18, 2004 Report Share Posted February 18, 2004 I guess I am a little lost as to why the petrol will penetrate. Here, there is a product available called Kreem (it can be seen on the web) not sure if it is available there or not. I believe it is also rated for Fiberglass tanks but I would have to verify that. My experience has been that at some point, it starts to cause more problems than it fixes. A well done, multiple layer, properly faired in fiberglass patch, will restore a standard fiberglass tank to a like new condition, and if properly painted or gel coated, will be un noticable. You could always take one of the two part epoxy putty sticks and gob it over the hole, and that would work, but not as well and would certainly be more noticable. Quote Link to comment Share on other sites More sharing options...
pa. Posted February 18, 2004 Report Share Posted February 18, 2004 Depending on the split you may be able to grind out a small amount of the glass then repack it with milled fibre and resin. This would be neater than glassing over a larger area. Make sure you sand back any area you are going to putting new resin onto as the paint will not hold the new materials. Gelcoat will need to be sanded to allow the new resin to get a chemical bond. On the inside of the tank ensure it is very clean and put some resin over the split area. Remember as resin goes off it generates heat so ensure the tank is as clean as you can get it so you don't have a fire. If there are raw fibres exposed to fluids the fluid will pass along the fibres. Don't buy your products from a hardware store but go to a boat shop or better still a fibreglass trade centre and buy the correct resin etc. Quote Link to comment Share on other sites More sharing options...
charliechitlins Posted February 18, 2004 Report Share Posted February 18, 2004 If you decide to use tank sealer, contact aircraft supply places. They'll sell you something that will probably say "Not for use in aircraft" on the can. Insurance liability, y'know. Quote Link to comment Share on other sites More sharing options...
feetupfun Posted February 19, 2004 Report Share Posted February 19, 2004 If you are going to the trouble of relining your fibreglass fuel tank, I suggest that you use low viscosity epoxy resin as the liner and buy it from an aircraft or boat repair supplier as previously suggested. The reason for this is that the automobile fuel or "gas" we buy will eventually contain ethanol if not already and polyester resin (which is what fibreglass fuel tanks are normally made of) is affected by ethanol. I'm not actually advising relining with anything unless it is absolutely necessary because it adds weight and can be a bit tricky to get evenly spread inside. Almost any fibreglass tank damage can be fixed by external repair if you take the advice already given on this string. David Lahey Australia Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.